1516:' race, where riders almost certainly would need to repack their coaster brakes after the grease melted or smoked due to the heat from lengthy downhill runs. A coaster brake can only be applied when the cranks are reasonably level, limiting how quickly it can be applied. As coaster brakes are only made for rear wheels, they have the disadvantage common to all rear brakes of skidding the wheel easily. This disadvantage may, however, be alleviated if the bicycle also has a hand-lever-operated front brake and the cyclist uses it. Another disadvantage is that the coaster brake is completely dependent on the chain being fully intact and engaged. If the chain breaks or disengages from the chainwheel and/or rear sprocket, the coaster brake provides no braking power whatsoever. Like all hub brakes except disc brakes, a coaster brake requires a reaction arm to be connected to the frame. This may require unbolting when the wheel is removed or moved in its fork ends to adjust chain tension.
257:
281:
1802:
620:
269:
1571:
329:
contacting the tyre, thus braking the front wheel. A tension spring held the rollers away from the tyre except when braking. Braking power was enhanced by an extra-long brake lever mounted in parallel with and behind the handlebar, which provided additional leverage when braking (two hands could be used to pull the lever if necessary). Used in combination with a rear coaster brake, a cyclist of the day could stop much more quickly and with better modulation of braking effort than was possible using only a spoon brake or rear coaster brake. Known colloquially as the
809:
989:
575:
293:
1437:
1164:
clearance; with rim brakes, this would be impossible, as the different rim sizes would not allow the same rim brakes to work with a different sized wheel. Wheel size optionality with disc brakes allows the rider more options, including using a smaller diameter rim-sized wheel (such as 27.5″+) with a higher volume wider tire with the same outer diameter size as a larger rim-sized wheel (such as 29″) – the outer diameter consistency is important as it preserves the geometry of the frame between the two different wheel sizes.
1361:
1041:
895:
1429:
647:
1733:
33:
864:
brakes. Mechanical (i.e. cable-actuated) disc brakes use the same amount of cable travel as V-brakes, except for those that are described as being "road" specific. As a general rule, mechanical disc brakes for so-called "flat bar" bicycles (chiefly mountain and hybrid bicycles) are compatible with V-brake levers, whereas mechanical disc brakes intended for "drop-bar" bicycles are compatible with the cable pull of older brake designs (cantilever, caliper, and U-brake).
3872:
393:
145:, were similarly braked with a spoon brake or by back pedalling. During its development from 1870 to 1878, there were various designs for brakes, most of them operating on the rear wheel. However, as the rear wheel became smaller and smaller, with more of the rider's weight over the front wheel, braking on the rear wheel became less effective. The front brake, introduced by John Kean in 1873, had been generally adopted by 1880 because of its greater stopping power.
412:
to wear unevenly. Over longer time and use, rims can become worn. Rims should be checked for wear periodically as they can fail catastrophically if the braking surface becomes too worn. Wear is accelerated by wet and muddy conditions. Rim brakes require that the rims be straight (not out-of-round or warped). If a rim has a pronounced wobble, then the braking force may be intermittent or uneven, and the pads may rub the rims even when the brake is not applied.
598:
209:
305:
742:
818:
1277:
480:
679:
1372:
882:. Mini V-brakes retain advantages specific to V-brakes such as not requiring extra cable stops. On the downside, their shorter arms provide very small tyre and wheel clearance and generally make for a less forgiving setup: they can only accommodate smaller tyre sizes compared to cantilever brakes, may pose problems for mounting fenders, can be clogged more easily by mud, and they can make it harder to change wheels.
1074:
1346:, reducing brake fade or failure. Downhill bikes usually have larger brakes to handle greater braking loads. Cross country bicycles usually use smaller rotors which handle smaller loads but offer considerable weight savings. It is also common to use a larger diameter rotor on the front wheel and a smaller rotor on the rear wheel since the front wheel does the most braking (up to 90% of the total).
1682:
generally inert, while DOT is corrosive to frame paint but has a higher boiling point. Using the wrong fluid can cause seals to swell or become corroded. A hydraulic mechanism is closed and therefore less likely have problems related to contamination at exposed areas. Hydraulic brakes rarely fail, but failure tends to be complete. Hydraulic systems require specialized equipment to repair.
616:, and result in better braking. Dual-pivot brakes are slightly heavier than conventional side-pull calipers and cannot accurately track an out-of-true rim, or a wheel that flexes from side to side in the frame during hard climbing. It is common to see professional racers climbing mountains with the quick-release undone on the rear brake, to eliminate drag from this source.
921:. As the cam presses against the follower it forces the arms apart. As the top of each arm moves outward, the brake shoe below the pivot is forced inward against the rim. There is much in favor of the roller cam brake design. Since the cam controls the rate of closure, the clamping force can be made non-linear with the pull. And since the design can provide positive
1268:
In recent years post mount has gained ground and is becoming more common. This is mostly due to decreased manufacturing and part cost for the brake calipers when using post mount. A limitation of the mount is that the location of the rotor is more constrained: it is possible to encounter incompatible hub/fork combinations, where the rotor is out of range.
451:
not necessarily provide more braking force, but will wear more slowly (in relation to thickness), so can usually be thinner. In general, a brake can be fitted with a variety of pads, as long as the mounting is compatible. Carbon fiber rims may be more sensitive to damage by incorrectly-matched brake pads, and generally must use non-abrasive cork pads.
753:. Because the arms move only in their designed arcs, the brake shoe must be adjustable in several planes. Thus cantilever brake shoes are notoriously difficult to adjust. As the brake shoes of a second-class cantilever brake wears, they ride lower on the rim. Eventually, one may go underneath the rim, so that the brake does not function.
980:
As the cam presses against the follower, the force is also transmitted to the other arm via the link. And specifically for suspension forks where the housing must terminate at the brake frame, the side-pull "sabre cam brake" was developed. In the sabre cam design, the cable end is fixed and the housing moves the single-sided cam.
1475:-made Perry Coaster Hub. Crude coaster brakes also exist, usually on children's bicycles, where a serrated steel brake cone grips the inside of the hub shell directly, with no separate brake pads or mantle. These offer a less progressive action and are more likely to lock the rear wheel unintentionally.
1234:
caliper" design. Single-actuation brakes use either a multi-part rotor that floats axially on the hub, or bend the rotor sideways as needed. Bending the rotor is theoretically inferior, but in practice gives good service, even under high-force braking with a hot disc, and may yield more progressiveness.
1605:
sheath, that rides in a u-shaped channel on the side of the wheel rim. Squeezing the brake lever tightens the cable against the channel to produce braking friction. A return spring slackens the cable when the brake lever is released, no adjustment is required, and the brake becomes more forceful when
791:
Originally, cantilever brakes had nearly horizontal arms and were designed for maximum clearance on touring or cyclo-cross bicycles. When the mountain bike became popular, cantilever brakes were adopted for these too, but the smaller MTB frames meant that riders often fouled the rear brake arms with
737:
designs exist; second-class is by far the more common. In the second-class lever design, the arm pivots below the rim. The brake shoe is mounted above the pivot and is pressed against the rim as the two arms are drawn together. In the first-class lever design, the arm pivots above the rim. The brake
589:
consist of two curved arms that cross at a pivot above the wheel and hold the brake pads on opposite sides of the rim. These arms have extensions on one side, one attached to the cable, the other to the cable housing. When the brake lever is squeezed, the arms move together and the brake pads squeeze
1681:
to push fluid through a hose to move pistons in a caliper, thus forcing pads against a braking surface. While hydraulic rim brakes exist, today the hydraulic actuation mechanism is identified mostly with disc brakes. Two types of brake fluid are used today: mineral oil and DOT fluid. Mineral oil is
1511:
Coaster brakes have the advantage of being protected from the elements and thus perform well in rain or snow. Though coaster brakes generally go years without needing maintenance, they are more complicated than rim brakes to repair if it becomes necessary, especially the more sophisticated type with
1470:
to move along the axle, driving the hub shell or gear assembly. When pedaling is reversed, the screw drives the clutch in the opposite direction, forcing it either between two brake shoes and pressing them against the brake mantle (which is a steel liner within the hub shell), or into a split collar
1383:
A Roller Brake is a modular cable-operated drum brake manufactured by
Shimano for use on specially splined front and rear hubs. Unlike a traditional drum brake, the Roller Brake can be easily removed from the hub. Some models contain a torque-limiting device called a power modulator designed to make
1296:
to secure the disc. The advantages of Center Lock are that the splined interface is theoretically stiffer, and removing the disc is quicker because it only requires one lockring to be removed. Some of the disadvantages are that the design is patented requiring a licensing fee from
Shimano. A Shimano
1242:
For disc brakes with a hydraulic system, high-performance calipers usually use two or three pistons per side; lower-cost and lower-performance calipers often have only one per side. Using more pistons allows a larger piston area and thus increased leverage with a given master cylinder. Also, pistons
1129:
The braking surface is farther from the ground and possible contaminants like mud which can coat or freeze on the rim and pads. With rim brakes, the first point that mud builds up on a mountain bike ridden in thick mud is usually the brakes. A mountain bicycle with disc brakes is less susceptible to
1004:
is a road bicycle brake named due to its triangular shape. The cable enters at the centre, pulls a corner of a parallelogram linkage housed inside the brake across two opposite corners, pushing out at the other two corners on to the brake arms above the pivots, so that the arms below the pivots push
593:
These brakes are simple and effective for relatively narrow tyres but have significant flex and resulting poor performance if the arms are made long enough to fit wide tyres. If not adjusted properly, low quality varieties tend to rotate to one side during actuation and tend to stay there, making it
228:
with solid rubber tyres in the 1800s and continued to be used after the introduction of the pneumatic-tyred safety bicycle. The spoon brake consists of a pad (often leather) or metal shoe (possibly rubber faced), which is pressed onto the top of the front tyre. These were almost always rod-operated
148:
Some penny-farthing riders used only back pedalling and got off and walked down steep hills, but most also used a brake. Having a brake meant that riders could coast down hill by taking their feet off the pedals and placing the legs over the handlebars, although most riders preferred to dismount and
1780:
of the brake lever must be matched to the brake it is connected to in order for the rider to have sufficient leverage and travel to actuate the brake. Using mismatched brakes and levers could result in too much mechanical advantage and hence not enough travel to properly actuate the brake (v-brakes
1719:
tandem bicycles used a cable from lever to a master cylinder mounted near the head tube, with a hydraulic line to the rear wheel caliper. Such "hybrid" designs allow the leverage of a hydraulic system while allowing use of cable brake levers, but may be heavier and can suffer from grit intrusion in
1706:
which is not hygroscopic and has varying boiling points depending on the type. O-rings and seals inside the brake are specifically designed to work with one or the other fluid. Using the incorrect fluid type will cause the seals to fail resulting in a "squishy" feeling in the lever, and the caliper
1267:
A disadvantage of post mounts is that the bolt is threaded directly into the fork lowers. If the threads are stripped or if the bolt is stuck, then the threads will need to be repaired, or the seized bolt drilled out. Frame manufacturers have standardized the IS mount for the rear disc brake mount.
1209:
There have been some problems using disc brakes with certain frame designs. Under hard braking, the front wheel can come out from the dropouts. The problem has occurred when the brake pads and dropouts are aligned so the brake reaction force tends to eject the wheel from the dropout. Under repeated
1175:
Disc brakes require a hub built to accept the disc, and a fork (for front brakes) or frame (for rear brakes) built to accept the caliper. Front hubs designed for discs often move the left hub's flange inward to make room for the disc, which causes the wheel to be dished. A dished wheel is laterally
979:
There are two rare variants that use the roller cam principle. For locations where centre-pull is inappropriate, the side-pull toggle cam brake was developed. Also a first-class cantilever, it uses a single-sided sliding cam (the toggle) against one arm that is attached by a link to the other arm.
859:
Since there is no intervening mechanism between the cable and the arms, the design is called "direct-pull". And since the arms move the same distance that the cable moves with regard to its housing, the design is also called "linear-pull". The term "V-brake" is trademarked by
Shimano and represents
411:
Rim brakes require regular maintenance. Brake pads wear down and have to be replaced. As they wear down, their position may need to be adjusted as the material wears away. Because the motion of most brakes is not perfectly horizontal, the pads may lose their centering as they wear, causing the pads
1503:
2×3. These use special extra-short derailleurs which can stand up to the forces of being straightened out frequently and do not require an excessive amount of reverse pedal rotation before the brake engages. Coaster brakes have also been incorporated into hub gear designs – for example the AWC and
1220:
There are two main types of disc brake: "mechanical" (cable-actuated) and hydraulic. Advantages and disadvantages are highly discussed by the users of each system. As advantages of cable-actuated disc brakes are argued lower cost, lower maintenance, and lighter system weight, hydraulic disc brakes
1116:
Many hydraulic disc brakes have a self-adjusting mechanism so as the brake pad wears, the pistons keep the distance from the pad to the disc consistent to maintain the same brake lever throw. Some hydraulic brakes, especially older ones, and most mechanical discs have manual controls to adjust the
1018:
criticized the delta brake for being heavy, giving mediocre stopping power, and suffering disadvantageous variable mechanical advantage. In particular, with a small parallelogram, pad wear causes mechanical advantage to rise dramatically. However, with high leverage, the stroke of the lever is not
863:
V-brakes function well with the suspension systems found on many mountain bikes because they do not require a separate cable stop on the frame or fork. Because of the higher mechanical advantage of V-brakes, they require brake levers with longer cable travel than levers intended for older types of
855:
pulls against the housing, the arms are drawn together. Because the housing enters from vertically above one arm yet force must be transmitted laterally between arms, the flexible housing is extended by a rigid tube with a 90° bend known as the "noodle" (a noodle with a 135° bend is used where the
450:
and can be replaced without moving the brake shoe from its alignment to the rim. The rubber can be softer for more braking force with less lever effort, or harder for longer life. Many pad designs have a rectangular shape; others are longer and curved to match the radius of the rim. Larger pads do
1825:
Adapters are available to allow the use of one type of lever with an otherwise incompatible type of rim brake. Some brake levers have adjustable leverage that can be made to work with either type of brake. Others vary their mechanical advantage as the lever moves to move the pad quickly at first,
1555:
are being used as drag brakes. (Some tandem riders with Avid BB-7 mechanical disc brakes and 203 mm rotors report fewer heat problems under heavy braking than when using the previous standard of comparison, an Arai drum used as a drag brake.) DT-Swiss make an adapter to mate disc rotors with
1419:
axle fastening, and removing a drum brake wheel requires the operator to disconnect the brake cable as well as the axle. They also require a torque arm which must be anchored to the frame or fork of the bicycle, and not all bicycles are constructed to accommodate such fastenings or tolerate their
867:
Poorly designed V-brakes can suffer from a sudden failure when the noodle end pulls through the metal stirrup, leaving the wheel with no braking power. Although the noodle can be regarded as a service item and changed regularly, the hole in the stirrup may enlarge through wear. The stirrup cannot
328:
used a rod operated by a lever on the handlebar to pull twin friction rollers (usually made of wood or rubber) against the front tyre. Mounted on axles secured by friction washers and set at an angle to conform to the shape of the tyre, the rollers were forced against their friction washers upon
1881:
Very loose surfaces (such as gravel and loose dirt): In some loose-surface situations, it may be beneficial to completely lock up the rear wheel in order to slow down or maintain control. On very steep slopes with loose surfaces where any braking will cause the wheel to skid, it can be better to
1723:
An older Sachs drum brake kit ("Hydro Pull") allows to rebuild a regular Sachs bicycle drum brake to hydraulic lever and action. A piston is added outside the drum instead of the bowden clamp. This solution is often seen on modified Long John cargo bikes, allowing a low friction lever pull front
1233:
Many disc brakes have their pads actuated from both sides of the caliper, while some have only one pad that moves. Dual actuation can move both pads relative to the caliper, or can move one pad relative to the caliper, then move the caliper and other pad relative to the rotor, called a "floating
1163:
Different wheel sizes can be used with the same frame: i.e. the same frame built for 29″ tires can often also fit 27.5″+ (650+) tires, despite the two wheel sizes having different rim diameters. This is possible with disc brakes, so long as the rotor sizes are consistent and the frame has enough
1058:
frames. They were available on some high-end mountain bikes in the early 1990s, but declined in popularity with the rise of disc brakes. The moderate performance advantage (greater power and control) they offer over cable actuated rim brakes is offset by their greater weight and complexity. Some
669:
These brakes were reasonably priced, and in the past filled the price niche between the cheaper and the more expensive models of side-pull brakes. They are more effective than side-pull brakes in long reach applications as the distance between the pivot and brake pad or cable attachment is much
454:
Ceramic-coated rims should be used with special pads because of heat build-up at the pad-rim interface; standard pads can leave a "glaze" on the ceramic braking surface, reducing its inherent roughness and leading to a severe drop in wet-weather braking performance. Ceramic pads usually contain
407:
are wet, and will brake unevenly if the rims are even slightly warped. Because rims can carry debris from the ground to the brake pads, rim brakes are more prone to clogging with mud or snow than disc brakes (where braking surfaces are higher from the ground), particularly when riding on unpaved
163:
which roughly resembles bicycles today, with two wheels of equal size, initially with solid rubber tyres. These were typically equipped with a front spoon brake and no rear brake mechanism, but like penny-farthings they used fixed gears, allowing rear wheel braking by resisting the motion of the
1850:". Light use of the rear brake causes a light skid as the bicycle approaches the limit where pitchover will occur, a signal to reduce force on the front brake. On a low-traction surface or when turning, the front wheel will skid, the bicycle cannot be balanced and will fall to the side instead.
1531:
A drag brake is intended to provide a constant decelerating force to slow a bicycle on a long downhill rather than to stop it; a separate braking system is used to stop the bicycle. A drag brake is often employed on a heavy bicycle such as a tandem in mountainous areas where extended use of rim
1336:
Rotors come in many different sizes, such as 160 mm (6.299 in) 185 mm (7.283 in) and 203 mm (7.992 in) diameter. Other sizes are available as manufacturers make discs specific to their calipers; the dimensions often vary by a few millimeters. Larger rotors provide
704:
U-brakes were used on mountain bikes through the mid-to-late 1980s, particularly under the chain stays, a rear brake mounting location that was then popular. This location usually benefits from higher frame stiffness, an important consideration with a powerful brake since flex in the stays will
1954:
This system emphasises the use of the rear brake, fails to optimise use of front braking, whilst being marketed as a solution to the fear of toppling over handle bars. The system encourages complacent use of brake levers by cyclists and reinforces the myth that the front brakes of bicycles are
1897:
It is customary to place the front brake lever on the left in right-side-driving countries, and vice versa, because the hand on the side nearer the centre of the road is more commonly used for hand signals. Placing the front brake lever on the right also mimics the layout on motorcycles and is
415:
During braking, the friction surfaces (brake pads and rims) will experience thermal heating. In normal use this is not a problem, as the brakes are applied with limited force and for a short time, so the heat quickly dissipates to the surrounding air. However, on a heavily laden bike on a long
194:
were introduced for the rear wheel. The coaster brake was contained in the rear wheel hub, and was engaged and controlled by backpedaling, thus eliminating the issue of tyre wear. In the United States, the coaster brake was the most commonly fitted brake throughout the first half of the 20th
712:
frames and forks. The U-brake's main advantage over cantilever and linear-pull brakes in this application is that sideways protrusion of the brake and cable system is minimal, and the exposed parts are smooth. This is especially valuable on freestyle BMX bikes where any protruding parts are
514:
and handlebars attach to the frame. A common setup was to combine a front rod brake with a rear coaster brake. Although heavy and complex, the linkages are reliable and durable and can be repaired or adjusted with simple hand tools. The design is still in use, typically on
African and Asian
1379:
Bicycle drum brakes operate like those of a car, although the bicycle variety use cable rather than hydraulic actuation. Two pads are pressed outward against the braking surface on the inside of the hub shell. Shell inside diameters on a bicycle drum brake are typically 70–120 mm
3518:
Polkupyörässä tulee olla ainakin yksi tehokas jarrulaite. Tavaran tai useamman kuin yhden henkilön kuljetukseen tarkoitetussa polkupyörässä, perävaunulla varustetussa polkupyörässä ja polkupyörässä, jossa on enemmän kuin kaksi vaihdetta, tulee kuitenkin olla kaksi erillistä tehokasta
175:, the use of spoon brakes began to decline, as they tended to quickly wear through the thin casing of the new tyres. This problem led to demands for alternative braking systems. On November 23, 1897, Abram W. Duck of Duck's Cyclery in Oakland, California, was granted a patent for his
1243:
may be of several sizes so pad force can be controlled across the face of the pad, especially when the pad is long and narrow. A long narrow pad may be desired to increase pad area and thus reduce the frequency of pad changes. In contrast, a single large piston may be heavier.
1950:
braking system uses a single lever to actuate the front brake using the friction applied to the back brake shoes by the rotation of the rear wheel from the rear brake. It is claimed this reduces the risk of some braking-related accidents including going over the handlebars.
408:
surfaces. The low price and ease of maintenance of rim brakes makes them popular in low- to mid-price commuter bikes, where the disadvantages are alleviated by the unchallenging conditions. The light weight of rim brakes also makes them desirable in road racing bicycles.
3521:[A bicycle must have at least one effective braking device. However, a bicycle intended for the transport of goods or more than one person, a bicycle equipped with a trailer and a bicycle with more than two gears must have two separate effective braking devices.]
885:
V-brakes always use thin and relatively long brake pads. The thin pads ease wheel removal, which is achieved by pushing the arms together and unhooking the noodle from the stirrup. The additional length gives good pad life by compensating for the thinner material depth.
2407:
1934:
is a type of close track racing in the UK, Poland, Australia, and France. The special built bike has a single freewheel and no brakes. Slowing is done during cornering by dragging the inside foot. These bikes are not intended for road use and are kept at the track.
1210:
hard braking, the axle moves in the dropout in a way that unscrews the quick release. Riders should make sure the skewers are properly tightened before riding. Forks that use different brake/dropout orientations or through-axles are not subject to this problem.
792:
their heels. "Low profile" cantilevers were designed to overcome this, where the arms are closer to 45 degrees from horizontal. Low profile brakes require more careful attention to cable geometry than traditional cantilevers but are now the most common type.
1768:
due to their mechanism of action which "interrupts" the cable run from the primary lever and actuates the brake by pushing the cable housing downward instead of pulling the cable. This type of lever is also known as a "cross lever" due to its popularity in
1186:
A front disc brake places a bending moment on the fork between the caliper anchor points and the tip of the dropout. In order to counter this moment and to support the anchor points and weight of the caliper, the fork must be of a certain size (most likely
503:, to transmit force applied to a hand lever to pull friction pads upwards against the inner surface, which faces the hub, of the wheel rim. They were often called "stirrup brakes" due to their shape. Rod brakes are used with a rim profile known as the
1414:
Drum brakes provide consistent braking in wet or dirty conditions since the mechanism is fully enclosed. They are usually heavier, more complicated, and often weaker than rim brakes, but they require less maintenance. Drum brakes do not adapt well to
458:
For wet-weather use, brake pads containing iron (iii) oxide are sometimes used as these have higher friction on a wet aluminum rim than the usual rubber. These salmon-colored pads were first made by Scott-Mathauser and are now produced by Kool-Stop.
1877:
Bumpy surfaces: If the front wheel comes off the ground during braking, its rotation will cease completely. Landing on a stopped front wheel with the brakes still applied is likely to cause the front wheel to skid and may flip the rider over the
333:, the design was used by many notable riders of the day, and was widely exported to England, Australia, and other countries. In 1902, Louis H. Bill was granted a patent for an improved version of the Duck Roller Brake (Patent 708,114) for use on
925:, maximum clamping force can be higher than that of other types of brakes. They are known for being strong and controllable. On the downside, they require some skill to set up and can complicate wheel changes. They also require maintenance: like
1193:
Heat build-up can lead to failure with disc brakes. Disc brakes heat discs in the same way as rim brakes heat rims, but discs provide an inherently smaller surface to dissipate heat. Excessive heat leads to boiling hydraulic fluid, resulting in
1724:
wheel brake action. After Sachs ceased production of this kit a similar solution is sometimes done by welding on a Magura piston to the drum cylinder lever. Welding was necessary because the Magura action is reverse to that of the Sachs kit.
1885:
Steep descents: the slope angle makes the front flip more easily achieved, and moreover a front-wheel skid would be very difficult to recover (crash highly probable), whereas a rear skid does still drag the bike without losing too much
1458:
integrated into the back hub with an internal freewheel. Freewheeling functions as with other systems, but when back pedaled, the brake engages after a fraction of a revolution. The coaster brake can be found in both single-speed and
1198:
or total failure. Overheating is more common in road cycling assuming the brakes are undersized to reduce weight. Recorded cases of disc brake failures usually involves several kilometers of downhill, combined with small underweight
1085:
consists of a metal disc, or "rotor", attached to the wheel hub that rotates with the wheel. Calipers are attached to the frame or fork along with pads that squeeze the rotors for braking. Disc brakes may be actuated mechanically by
1650:
to move brake arms, thus forcing pads against a braking surface. Cable mechanisms are usually less expensive, but may require some maintenance related to exposed areas of the cable. Other mechanical actuation mechanisms exist: see
657:
have symmetrical arms and therefore centre more effectively. The cable housing attaches to a fixed cable stop attached to the frame, and the inner cable bolts to a sliding piece (called a "braking delta", "braking triangle", or
3114:
Ibid. "Direct pull cantilevers have twice as much mechanical advantage as traditional brakes, so they require a lever with half as much mechanical advantage. Long pull levers pull the cable twice as far, but only half as
256:
1889:
Long descents: alternating the front and back brake can help prevent hand fatigue and overheating of the wheel rims which can cause a disastrous tyre blow-out, or boiling of the hydraulic fluid in case of hydraulic disc
1744:
within easy reach of the rider's hands. They may be distinct from or integrated into the shifting mechanism. The brake lever transmits the force applied by the rider through either a mechanical or hydraulic mechanism.
697:. The difference is that the two arm pivots attach directly to the frame or fork while those of the centre-pull caliper brake attach to an integral bridge frame that mounts to the frame or fork by a single bolt. Like
462:
To minimise excessive rim wear, a brake pad should be hard enough that it does not embed road grit or chips of rim metal in the face of the pad, since these act as grinding/gouging agents and markedly reduce rim life.
419:
A ceramic coating for the rims is available which may reduce wear and can also improve both wet and dry braking. It may also slightly reduce heat transfer to the inside of the rims because it is a thermal insulator.
1752:
may have more than one brake lever for each brake to facilitate braking from multiple hand positions. Levers that allow the rider to work the brakes from the tops of the bars, introduced in the '70s, were called
1301:
tool in case of through-axle hub) is needed to remove the rotor and is more expensive and less common than a Torx key. Advantages of IS six-bolt are that there are more choices when it comes to hubs and rotors.
543:-actuated brake in which the brake mounts to a single point above the wheel, theoretically allowing the arms to auto-centre on the rim. Arms extend around the tyre and end in brake shoes that press against the
784:. It is a centre-pull cantilever design with an outwardly angled arm protruding on each side, a cable stop on the frame or fork to terminate the cable housing, and a straddle cable between the arms similar to
1917:
may also lack brakes, and slowing or stopping is accomplished as with a track bike. Many fixed gear bikes however are fitted with a front brake for safety reasons, or because it is a legal requirement. Some
149:
walk down steep hills. Putting the legs under the handlebars with the feet off the pedals placed on foot-rests on the forks had resulted in serious accidents caused by the feet getting caught in the spokes.
1182:
The torque moment must be transmitted to the tyre through the wheel components: flanges, spokes, nipples, and rim spoke bed. An engineered disc brake would reduce weight by not having most of the metal rim
3278:[Your bike must meet several technical requirements. If you want to hit the road, then your bicycle must be equipped with: good brakes front and rear; for children's bikes one brake is sufficient]
1341:
for the caliper to act on. Smaller rotors provide less braking torque but also less weight and better protection from knocks. Larger rotors dissipate heat more quickly and have a larger amount of mass to
856:
front brake is operated by the right hand, as this gives a smoother curve in the cable housing). The noodle is seated in a stirrup attached to the arm. A flexible bellows often covers the exposed cable.
3402:
1153:
The use of very wide tyres favors disc brakes, as rim brakes require ever-longer arms to clear the wider tyre. Longer arms tend to flex more, degrading braking. Disc brakes are unaffected by tyre width.
594:
difficult to evenly space brake shoes away from the rim. These brakes are now used on inexpensive bikes; before the introduction of dual-pivot caliper brakes they were used on all types of road bikes.
1054:
are one of the least common types of brakes. They are mounted either on the same pivot points used for cantilever and linear-pull brakes or they can be mounted on four-bolt brake mounts found on many
2220:, who crossed the United States aboard a motorized bicycle with a Duck roller brake praised its efficiency, stating that "I controlled my motor with it on the steepest grades of the Rocky Mountains".
860:
the most popular implementation of this design. Some high-end v-brakes use a four-pivot parallel motion so the brake pads contact at virtually the same position on the wheel rim regardless of wear.
1826:
then provide more leverage once it contacts the brake surface. Hydraulic brake levers move a piston in a fluid reservoir. The mechanical advantage of the lever depends on the brake system design.
1586:
that rotates with a wheel and is pulled tight to generate braking friction. Band brakes appeared as early as 1884 on tricycles. Star Cycles introduced a band brake in 1902 on its bicycles with
1380:(2.756–4.724 in). Drum brakes have been used on front hubs and hubs with both internal and external freewheels. Both cable- and rod-operated drum brake systems have been widely produced.
612:. One arm pivots at the centre, like a side-pull; and the other pivots at the side, like a centre-pull. The cable housing attaches like that of a side-pull brake. These brakes offer a higher
3124:
To solve the problem of using V-brakes with road levers, devices that use an eccentric pulley to increase the amount of cable pull of road levers, such as the "QBP Travel Agent", may be used.
705:
increase lever travel and reduce effective braking force. Unfortunately it is also very prone to clogging by mud, which meant that U-brakes quickly fell out of favour on cross-country bikes.
3448:
I velocipedi devono essere muniti di pneumatici, nonché: a) per la frenatura: di un dispositivo indipendente per ciascun asse che agisca in maniera pronta ed efficace sulle rispettive ruote
1548:. As of 2011, the Arai drum brake has been out of production for several years, with remaining stocks nearing depletion and used units commanding premium prices on internet auction sites.
138:
to press onto the rear wheel. The brake was operated by a lever or by a cord connecting to the handlebars. The rider could also slow down by resisting the pedals of the fixed-wheel drive.
3276:
Uw fiets moet aan verschillende technische eisen voldoen. Als u de weg op wil, dan moet uw fiets uitgerust zijn met: goede remmen vooraan en achteraan; bij kinderfietsjes volstaat Ă©Ă©n rem
2170:, pp. 198–233: "The spoon brake was fairly ineffective, while the coaster brake did not operate on the front tyre, the most effective position on a two-wheel vehicle during a hard stop."
1478:
Unlike most drum brakes (but like a
Shimano Roller Brake) a coaster brake is designed to run with all its internal parts coated in grease for quiet operation and smooth engagement. Most
795:
Traditional cantilever brakes are difficult to adapt to bicycle suspension and protrude somewhat from the frame. Accordingly, they are usually found only on bicycles without suspension.
164:
pedals. The relative fragility of the wooden rims used on most bicycles still precluded the use of rim brakes. In the late 1890s came the introduction of rim brakes and the freewheel.
280:
1874:
Slippery surfaces, such as wet pavement, mud, snow, ice, or loose stones/gravel. It is difficult to recover from a front-wheel skid on a slippery surface, especially when leaned over.
1221:
are said to offer more braking power and better control. Cable-actuated disc brakes were traditionally the only type of disc brake that could be used with the brake levers found on
1142:
It is possible to ride a bicycle with a buckled wheel if it has disc brakes, where it would not be possible with a rim brake because the buckled wheel would bind on the brake pads.
1882:
maintain control of the bicycle by the rear brake more than one would normally. However neither wheel should stop rotating completely, as this will result in very little control.
438:, with a post or bolt on the back to attach to the brake. Some are made as one piece with the attachment directly molded in the pad for lower production costs; brake pads of the
1861:
and other specialized bicycles), the lower relative centre of mass makes it virtually impossible for heavy front braking to flip the bicycle; the front wheel would skid first.
1512:
expanding brake shoes. Coaster brakes also do not have sufficient heat dissipation for use on long descents, a characteristic made legendary through events such as the 'Repack
1913:. Since track bikes have a fixed gear, braking can be accomplished by reversing the force on the pedals to slow down, or by locking the pedals backwards and inducing a skid.
1626:
is that part of the brake system that transmits force from the rider to that part of the system that does the actual braking. Brake system actuation mechanisms are either
250:
supplementally on adult bicycles until the 1930s, and on children's bicycles until the 1950s. In the developing world, they were manufactured until much more recently.
701:, this is a caliper design with pivots located above the rim. Thus U-brakes are often interchangeable with, and have the same maintenance issues as, roller cam brakes.
2910:
1179:
A rim brake works directly on the rim and the attached tyre; a disc brake applies a potentially large torque moment at the hub. The latter has two main disadvantages:
1926:. The usual method of stopping is for the rider to put one or both feet on the ground, or to wedge a foot between the seat and the rear tyre, effectively acting as a
1133:
Disc brakes may be made of materials that dissipate heat better than the wheel rim, but undersized sport-sized discs will be too small to take advantage of this fact.
1938:
In
Belgium, Australia, Germany, the UK, France, Italy, Poland, Japan, Denmark, Sweden, and Finland, it is illegal to ride a bicycle without brakes on a public road.
878:) are V-brakes with shorter arms, typically between 8 and 9 centimeters. This reduces the required cable pull, making them compatible with brake levers intended for
788:. The cable from the brake lever pulls upwards on the straddle cable, causing the brake arms to rotate up and inward thus squeezing the rim between the brake pads.
156:
patented by
Browett and Harrison in 1887. This early version of caliper braking used a rubber block to contact the outside of the penny-farthing's small rear tyre.
4306:
2717:
1448:
Invented in 1898 by
Willard M. Farrow, the "coaster brake", also known as a "back pedal brake" or "foot brake" ("torpedo" or "contra" in some countries, in Italy
1176:
weaker when forced to the non-disc side. Other hubs use conventional flange spacing and provide a wheel without dish, but require a less common wide-spaced fork.
507:, which has a slightly concave area on the braking surface and lacks the flat outer surface required by brakes that apply the pads on opposite sides of the rim.
1781:
with conventional levers) or too little mechanical advantage, requiring a very strong pull to apply the brakes hard (v-brake levers with other types of brake).
1868:
When unfamiliar with the braking characteristics of a bicycle. It is important to test the brakes and learn how much hand force is needed when first riding it.
1026:
in 1985, but brakes based on the same mechanism were also manufactured by Modolo (Kronos), Weinmann, and others. They are no longer made and are now uncommon.
268:
666:
connecting the two brake arms. Tension on the cable is evenly distributed to the two arms, preventing the brake from taking a "set" to one side or the other.
1715:
Some older designs, like the AMP and
Mountain Cycles brakes, use a cable from lever to caliper, then use a master cylinder integrated into the piston. Some
3487:
2234:
1707:
pistons are unable to retract, so a scraping disc is common. The brake fluid reservoir is usually marked to indicate the type of brake fluid to be used.
3559:
2932:
2810:
1846:
on the front wheel. If the front brake is used too hard, momentum may cause the rider and bike to pitch forward – a type of crash sometimes called an "
1791:
levers work with most brake designs, including caliper brakes, traditional cantilever brakes, and mechanically actuated disc brakes branded for "Road".
1059:
e-bikes continue to use them since they are powerful, relatively low-maintenance and weight is less of an issue when electric assistance is available.
1019:
enough to fully apply the brake, so the rider can have brakes that feel normal in light braking but which cannot be applied harder for hard braking.
547:. While some designs incorporate dual pivot points — the arms pivot on a sub-frame — the entire assembly still mounts to a single point.
2537:
1955:
dangerous. Since this system means that the brakes on both wheels are directly tied together, the legality of such a system varies based on nation.
3293:
1958:
Cyclists young and old should seek training in the effective use of both brakes to stop in the minimum possible stopping distance in an emergency.
3514:"Liikenne- ja viestintäministeriön asetus kaksi- ja kolmipyöräisten ajoneuvojen sekä nelipyörien rakenteesta ja varusteista, Luku 5, 17 § Jarrut"
749:
Due to a wider possible distance between the mounts and pads, cantilever brakes are often preferred for bicycles that use wide tyres, such as on
416:
descent, heat energy may be added more quickly than it can dissipate causing heat build-up, which may damage components and cause brake failure.
3056:
2618:
1150:
While all types of brakes will eventually wear out the braking surface, a brake disc is easier and cheaper to replace than a wheel rim or drum.
3003:
240:. It consists of a spring-loaded flap attached to the back of the fork crown. This is depressed against the front tyre by the rider's foot.
243:
Perhaps more so than any other form of bicycle brake, the spoon brake is sensitive to road conditions and increases tyre wear dramatically.
1797:
levers work with "direct-pull" cantilever brakes, such as
Shimano "V-Brakes", and mechanically actuated disc brakes branded for "Mountain".
399:
rim worn out by V-brakes. The outer wall has been worn through and the wheel is dangerously weakened. This is a disadvantage of rim brakes.
403:
Rim brakes are inexpensive, light, mechanically simple, easy to maintain, and powerful. However, they perform relatively poorly when the
4301:
3476:[A bicycle must be equipped with at least two independent braking systems that act on the front and rear wheels respectively.]
3450:[Bicycles must have tires and a) for braking: an independent system for every axle acting quick and effectively on each wheel]
1784:
Mechanical (cable) brake levers come in two varieties based on the length of brake cable pulled for a given amount of lever movement:
638:. Individual mounting points for each arm ease the centering of side-pull brakes, and accommodate tire widths of 30 mm and more.
2660:
1471:
and expanding it against the mantle. The braking surface is often steel, and the braking element brass or phosphor-bronze, as in the
2836:(3rd ed.), p. 245: "The front brake therefore has to provide 90 percent of the total retarding force at a deceleration of 0.5 G ..."
4134:
3791:
2686:
246:
Though made obsolete by the introduction of the Duck brake, coaster brake, and rod brake, spoon brakes continued to be used in the
2369:
3392:
as regulated by the Electrically Assisted Pedal Cycles Regulations 1983 (amended 2015), and regulation 7(1)(a) to other bicycles.
1611:
3166:
2515:
3383:
3345:
3671:
3533:
3139:
2313:
4411:
4270:
2014:
1893:
Flat front tyre: braking a tyre that has little air can cause the tyre to come off the rim, which is likely to cause a crash.
1544:, whose brakes are screwed onto hubs with conventional freewheel threading on the left side of the rear hub and operated via
434:
Brake pads are available with numerous shapes and materials. Many consist of a replaceable rubber pad held on a mounting, or
183:
used a rod operated by a lever on the handlebar to pull twin rubber rollers against the front tyre, braking the front wheel.
17:
3600:
2906:
2571:
2275:
Rim brakes have been the subject of countless "engineering innovations". Some of the more unusual results can be seen here
1835:
1280:
Center Lock hub: The disc mounts on the splines on the outside and is secured by a lockring engaging the internal thread.
2724:
304:
2605:
There have been concerns about the safety of front disc brakes, in conjunction with lightweight quick-release skewers.
1801:
212:
Spoon brake on antique Peugeot 'open diamond' frame 'Le Lion model B' at the Batavus Museum in Heerenveen, Netherlands
3759:
3738:
3710:
3039:
2494:
2167:
2074:
2046:
1139:
Wheel rims tend to be made of lightweight metal. Brake discs and pads are harder and can accept higher maximum loads.
63:
Most bicycle brake systems consist of three main components: a mechanism for the rider to apply the brakes, such as
3644:
3618:
1384:
it difficult to skid the wheel. In practice this can reduce its effectiveness on bicycles with adult-sized wheels.
826:
Linear-pull brake on rear wheel of a mountain bike (left). A noodle; the bellows is directly above the tyre (right)
1125:
Disc brakes tend to perform equally well in all conditions including water, mud, and snow due to several factors:
3263:
1967:
1485:
Coaster-brake bicycles are generally equipped with a single cog and chain wheel and often use an 3.2-millimeter (
2405:, Cunningham, Charles B., "Caliper brake for mountain bicycles having wide tires", issued 1988-08-23
929:, as the pad wears it strikes the rim higher; unless re-adjusted it can eventually contact the tyre's sidewall.
4265:
3474:
En cykel skal være forsynet med mindst to uafhængige bremsesystemer, der virker på henholdsvis for- og baghjul.
2238:
851:. However, the arms are longer, with the cable housing attached to one arm and the cable to the other. As the
292:
4382:
2958:
2936:
4066:
2806:
1251:
There are many standards for mounting disc brake calipers. However, most manufactures today use either the
1012:
Many consider the brake attractive, and it has a lower wind profile than some other common brakes. However,
4127:
3784:
2287:
1864:
In some situations, it is advisable to slow down and to use the rear brake more and the front brake less:
3289:
2538:"The rise of disc brakes at the Tour de France + top tip from a pro mechanic for setting up disc brakes"
1206:
racks not designed for them. For this reason, many manufacturers produce "disc" and "non-disc" versions.
224:
was probably the first type of bicycle brake and precedes the pneumatic tyre. Spoon brakes were used on
3923:
483:
Rod brake system. Lateral play in the pivot for the rear brake rod allows for rotation of the handlebar
2402:
131:
4296:
4086:
2373:
1479:
550:
Caliper brakes tend to become less effective as tyres get wider, and so deeper, reducing the brakes'
2750:
2622:
1770:
4337:
1513:
1136:
There are holes in the rotor, providing a path for water and debris to get out from under the pads.
36:
Animation of a single pivot side-pull caliper brake for the rear wheel of a steel framed road bike.
3431:
1130:
mud buildup provided the rear frame and front fork yoke have sufficient clearance from the wheels.
1055:
4421:
4311:
4120:
3777:
2230:
1556:
hubs threaded for the Arai drum brake, but this still leaves the problem of fitting the caliper.
1298:
738:
shoe is mounted below the pivot and is pressed against the rim as the two arms are forced apart.
2436:
670:
shorter, reducing flex. It is important that the fixed bridge holding the pivots is very stiff.
4406:
4157:
3990:
3831:
1843:
1760:
or, due to their reputation for being unable to actuate the full range of travel of the brake,
1598:
1009:
varies as a tangent function across its range, where that of most other designs remains fixed.
937:
725:
is a class of brake in which each arm is attached to a separate pivot point on one side of the
1847:
619:
4372:
4177:
3800:
3073:
3031:
3025:
2781:
2489:(6th ed.). Berkeley, California, USA: Sutherland Publications. pp. 13.27 to 13.28.
2091:
1982:
1441:
3513:
3162:
2715:
sells no fewer than 13 different adapters to fit their brakes to various mounting patterns.
122:
included a pivoting brake shoe that could be pressed against the rear iron tyre of his 1817
4352:
4219:
3913:
3461:
1806:
1777:
1416:
1006:
922:
613:
551:
1749:
1610:
used on industrial machinery. The Yankee bicycle only included a rear brake, but that met
1508:, and the Shimano Nexus 3-speed. They can have up to eight gears, like the Nexus inter-8.
1222:
1190:
The heavier fork and wheels compound the weight disadvantage of the brake assembly itself.
8:
4316:
4212:
4192:
3945:
3821:
3722:
3698:
3318:
3088:
1977:
1495: in) wide chain. However, there have been several models of coaster brake hubs with
957:
953:
439:
1898:
advantageous to avoid confusion when switching to and from a pedal cycle to motorcycle.
988:
808:
630:
employ two mounting points, increasing stiffness and braking power. It was developed by
4259:
4250:
4172:
4162:
3861:
3378:
3135:
2858:
2648:
2558:
2461:
2377:
1914:
1570:
1157:
933:
848:
516:
237:
3321:[Road Traffic Licensing Regulations] (in German). German Department of Justice
1117:
pad-to-rotor gap. Several adjustments are often required during the life of the pads.
894:
4202:
4197:
3871:
3816:
3755:
3734:
3706:
3679:
3534:"Hey, Parents, Meet the Safest Bike for Your Children. (The Secret Is in the Brakes)"
3103:
3035:
2511:
2490:
2163:
2070:
2042:
2010:
1858:
1741:
1285:
1014:
973:
381:
334:
2424:
1105:. Towards the end of the 2010s, disc brakes have become increasingly common also on
868:
normally be replaced, so good-quality V-brakes use a durable metal for the stirrup.
574:
262:
Spoon brake on front wheel of 1886 Swift Safety Bicycle at Coventry Transport Museum
4056:
3687:
3389:
3021:
1814:
1496:
1436:
1324:
1022:
The basic design dates from at least the 1930s. They were made most prominently by
230:
4071:
3592:
3306:
A person shall not ride a bicycle that does not have at least one effective brake.
510:
The rear linkage mechanism is complicated by the need to allow rotation where the
356:
of the rotating wheel, thus slowing it and the bicycle. Brake pads can be made of
4416:
4367:
4321:
4187:
4167:
4101:
4061:
4041:
3727:
3373:
3236:
2894:
2341:
2217:
1909:
are built without brakes so as to avoid sudden changes in speed when racing on a
1839:
1672:
1388:
1318:
1289:
1102:
1035:
917:
designs exist; first-class is most common and is described here.) Each arm has a
910:
404:
2356:
1813:) the attachment point of the cable is moved outward. For use with conventional
1466:
When such a hub is pedaled forwards, the sprocket drives a screw which forces a
4362:
4096:
4026:
3851:
3846:
3290:"Western Australian Consolidated Regulations, Road Traffic Code 2000 – Reg 224"
3193:
3189:
2661:"CXM Tech Exclusive: Drop Bar Hydraulic Disc Brake Adapter Tested at Nationals"
2593:
1931:
1854:
1716:
1541:
1533:
1505:
1404:
1364:
1360:
1106:
1098:
609:
555:
225:
160:
142:
104:
100:
76:
2879:
2180:
Parliamentary Debates: Senate and House of Representatives, Tariff Preferences
1690:
Hydraulic disc brakes make use of two common forms of fluid: Automotive grade
4400:
4182:
4143:
4076:
4046:
3941:
3931:
3880:
3808:
3683:
1922:
bicycles are built without brakes to forgo the expense and complication of a
1906:
1818:
1663:
were actuated by a cable that was pulled by twisting the end of a handlebar.
1428:
1343:
1284:
There are many options for rotor mounting. IS is a six-bolt mount and is the
1094:
1040:
945:
750:
726:
709:
646:
635:
579:
524:
520:
365:
247:
191:
172:
84:
68:
3462:"Cykelbekendtgørelsen – Bekendtgørelse om cyklers indretning og udstyr m.v."
3220:
2274:
1732:
1528:
is a type of brake defined by its use rather than by its mechanical design.
32:
4291:
4255:
4234:
4031:
3995:
3898:
3888:
3836:
3588:
1736:
Brake levers on the drop handlebars of a road bike with integrated shifters
1647:
1545:
1087:
949:
918:
852:
730:
713:
susceptible to damage and may interfere with the rider's body or clothing.
559:
540:
511:
504:
500:
168:
125:
72:
2980:
1262:
733:. Thus all cantilever brakes are dual-pivot. Both first- and second-class
233:, a foot-operated form of the spoon brake sometimes is retrofitted to old
4229:
4224:
4091:
4036:
4000:
3950:
2845:
2751:"Disc brake rotors explained | How to find the right rotor for your bike"
2712:
1703:
1699:
1482:
work well in a coaster brake, with its metal-to-metal friction surfaces.
1392:
1312:
International Standard (IS), 6-Bolt 44 mm bolt circle diameter (BCD)
1044:
961:
392:
353:
108:
57:
3648:
3622:
964:. It is not unusual for a bicycle to have a single roller cam brake (or
4377:
4357:
4207:
4081:
3960:
3903:
1764:. Modern top-mounted brake levers are considered safer, and are called
1607:
1565:
1472:
1400:
1396:
1355:
1338:
1337:
greater braking torque for a given pad pressure, by virtue of a longer
1195:
1068:
1023:
993:
597:
499:
in Raleigh terminology), uses a series of rods and pivots, rather than
447:
435:
373:
130:. This was continued on the earliest bicycles with pedals, such as the
119:
274:
Spoon brake variation at the Batavus Museum in Heerenveen, Netherlands
208:
4286:
4051:
3969:
3826:
3597:
Jobst Brandt: Frequently Asked Questions about Bicycles and Bicycling
3249:
2006:
1972:
1923:
1910:
1587:
1156:
Unlike some rarer rim brake designs, disc brakes are compatible with
1093:
Disc brakes are most common for mountain bikes (including nearly all
960:
for improved stiffness as they do not protrude to interfere with the
443:
429:
396:
349:
187:
3419:
Tout cycle doit ĂŞtre muni de deux dispositifs de freinage efficaces.
756:
There are several brake types based on the cantilever brake design:
3974:
3964:
3936:
3856:
3841:
2687:"Shimano introduces road hydro disc brakes for mechanical shifting"
1947:
1500:
1460:
1293:
1077:
A hydraulic front disc brake. The disc is held by a six-bolt mount.
969:
741:
96:
3361:... brakeless riders are strictly breaking the law in the UK.
2782:"How to fit disc rotors: get fresh brake surfaces in 8 easy steps"
1809:(leverage) can be adjusted. For use with direct-pull cantilevers (
1276:
678:
479:
195:
century, often comprising the only braking system on the bicycle.
95:, to press two or more surfaces together in order to convert, via
4112:
4010:
3908:
1810:
1695:
1371:
1203:
941:
817:
631:
357:
45:
3769:
3560:"World's Safest Children's Bikes on Shark Tank – Guardian Bikes"
1601:
in the 1990s, consists of a stainless-steel cable, wrapped in a
3955:
3333:[Bicyclists must have two mutually independent brakes.]
1602:
1583:
1467:
1305:
Adaptors enable the use of six-bolt discs on Center Lock hubs.
361:
1073:
286:
Bicycle spoon brake on 1898 Columbia Model 51 Ladies Chainless
152:
An alternative to the spoon brake for penny-farthings was the
4347:
3893:
1871:
When leaning in a turn (or preferably, brake before turning).
1691:
1202:
The design and positioning of disc brakes can interfere with
1005:
pads in against the rim. A feature of the design is that the
914:
734:
369:
3331:
Fahrräder müssen zwei voneinander unabhängige Bremsen haben.
2041:. Shire publications, Princes Risborough UK. pp. 8–15.
48:
or prevents the wheels from moving. The two main types are:
2314:"Campagnolo (finally) releases Direct Mount brake calipers"
659:
348:
are so called because braking force is applied by friction
3733:(3rd (paperback) ed.). Cambridge, MA: The MIT Press.
3705:(2nd (hardcover) ed.). Cambridge, MA: The MIT Press.
968:) combined with another type. They are still used on some
471:
The following are among the many sub-types of rim brakes:
2216:
Duck Brake Company, Testimonial of Geo. A. Wyman (1903):
1919:
1590:. Band brakes are still manufactured for bicycles today.
1259:(PM) standards. These differ by disc size and axle type.
909:
actuated by the cable pulling a single two-sided sliding
4307:
Electro-pneumatic brake system on British railway trains
3205:
A tandem with an adult stoker will skid instead of flip.
2619:"Disk brakes and quick releases - what you need to know"
1582:
consists of a band, strap, or cable that wraps around a
3502:[By law, a bicycle must always have ... brakes]
2572:"Road Bike Disc Brakes Are Coming, But Will They Work?"
2205:
United States Patent Office, Letters Patent No. 708,114
2114:
United States Patent Office, Letters Patent No. 594,234
1642:
The primary modern mechanical actuation mechanism uses
1263:
Advantages and disadvantages of various types of mounts
1215:
3374:"Pedal Cycles (Construction and Use) Regulations 1983"
3057:"Break Fluid Breakdown and Implications for Road disc"
1375:
Shimano Roller Brake unit on an internally geared hub
1659:
for a mechanism incorporating metal rods. The first
1540:. The largest manufacturer of this type of brake is
71:; a mechanism for transmitting that signal, such as
3726:
2935:. Wolverhampton Museum of Industry. Archived from
2907:"TRICYCLES v BICYCLES predated CARS v MOTORCYCLES"
2162:(2nd ed.), Massachusetts Institute of Technology,
1113:for controlled speed reduction on steep descents.
757:
310:Improvised spoon brake on a Chinese cargo tricycle
3754:(in Swedish) (1st ed.). Bokförlaget Prisma.
3346:"Cycling without brakes? You're breaking the law"
1842:to the front wheel during braking, improving the
1532:brakes could cause a rim to become hot enough to
554:. Thus caliper brakes are rarely found on modern
4398:
1941:
1288:. Center Lock is patented by Shimano and uses a
956:in the standard locations, as well as below the
948:in the 1980s and into the 1990s, mounted to the
906:
775:
2397:
2395:
1308:Examples of mounting standards are shown here:
785:
694:
387:
159:The 1870s and 1880s saw the development of the
3749:
3678:(Winter 2008). Vintage Bicycle Press LLC: 36.
2000:
1857:and other long-wheel-base bicycles (including
839:, commonly referred to by Shimano's trademark
4128:
3785:
3500:Enligt lag mĂĄste en cykel alltid ha ... broms
2158:Whitt, Frank R. and Wilson, David G. (1982),
1449:
1246:
932:The roller cam design was first developed by
641:
563:
3266:[Obligations of cyclists] (in Dutch)
2392:
2130:
2128:
2126:
2124:
2122:
2001:Hadland, Tony; Lessing, Hans-Erhard (2016).
1702:and has a boiling point of 230 °C; and
1228:
123:
3531:
3118:
2092:"Myths and Milestones in Bicycle Evolution"
780:Traditional cantilever brakes pre-date the
745:Low profile 'traditional' cantilever brake.
569:
4302:Electronically controlled pneumatic brakes
4297:Diesel electric locomotive dynamic braking
4135:
4121:
3792:
3778:
3319:"StraĂźenverkehrs-Zulassungs-Ordnung StVZO"
2869:
2487:Sutherlands Handbook for Bicycle Mechanics
2484:
1901:
1536:.; The typical drag brake has long been a
1271:
1109:. A disc brake is sometimes employed as a
376:". Rim brakes are typically actuated by a
3557:
2959:"Band Brake detailed product information"
2285:
2119:
2032:
2030:
2028:
2026:
1655:for back-pedal actuation mechanisms, and
1606:wet. Husted said his inspiration was the
693:) are essentially the same design as the
3672:"Slow Down, The Story of Bicycle Brakes"
2748:
2569:
2485:Sutherland, Howard; et al. (1995).
2286:Loveridge, Matthew (20 September 2018).
2182:, Volume 34 (19 September 1906), p. 4951
2060:
2058:
1800:
1740:Brake levers are usually mounted on the
1731:
1685:
1656:
1569:
1435:
1427:
1370:
1359:
1275:
1072:
1039:
987:
893:
764:– both second class lever designs – and
740:
677:
662:") or a small pulley, over which runs a
645:
618:
596:
573:
478:
391:
234:
207:
190:coasting mechanisms, the first internal
80:
31:
3343:
3054:
3020:
2259:
2069:. London: Studio Editions. p. 32.
2036:
1617:
1612:U.S. Consumer Product Safety Commission
1297:cassette lockring tool (or an external
1029:
944:. Roller cam brakes were used on early
167:With the introduction of mass-produced
14:
4399:
3623:"Articles by Sheldon Brown and Others"
3617:
3587:
3551:
3232:
3216:
2909:. www.triporteurs.co.uk. 2 July 2009.
2890:
2779:
2644:
2554:
2457:
2352:
2337:
2311:
2089:
2064:
2023:
2003:Bicycle Design: An Illustrated History
1574:Band brake for rear wheel of a bicycle
879:
844:
765:
698:
474:
466:
141:The next development of bicycles, the
4271:Westinghouse Brake and Signal Company
4116:
3773:
3669:
3643:
3169:from the original on 13 December 2010
3142:from the original on 23 December 2010
3099:
3084:
3069:
3001:
2875:
2775:
2773:
2771:
2616:
2610:
2472:
2420:
2367:
2288:"Why direct-mount brakes are awesome"
2264:. Vol. 1. Elsevier. p. 170.
2055:
708:U-brakes are the current standard on
587:Single-pivot side-pull caliper brakes
3750:Ekström, Gert; Husberg, Ola (2001).
3603:from the original on 3 February 2009
3187:
2813:from the original on 9 November 2006
2711:As a point of reference, as of 2010
2229:
1829:
1407:often employ a rear drum brake as a
889:
716:
689:(also known by the trademarked term
558:. But they are almost ubiquitous on
87:; and the brake mechanism itself, a
3593:"Brakes from Skid Pads to V-brakes"
3558:Alexander, Jeremy (18 April 2017).
3525:
3344:Sparkes, Matthew (25 August 2010).
3136:"The Geometry of Cantilever Brakes"
2448:Drawings and technical description.
1652:
1237:
606:Dual-pivot side-pull caliper brakes
455:chromium compounds to resist heat.
153:
24:
4142:
2913:from the original on 28 March 2010
2768:
2518:from the original on 14 March 2010
2312:Arthur, David (4 September 2015).
1480:grey molybdenum disulphide greases
1391:in some countries, especially the
1225:, but this is no longer the case.
772:– both first class lever designs.
564:dual-pivot side-pull caliper brake
25:
4433:
3799:
3532:Popomaronis, Tom (20 July 2017).
3160:
3133:
3030:. Yale University Press. p.
2591:
2570:Benedict, Tyler (February 2012).
1927:
1678:
1660:
1643:
1423:
1315:Center Lock (Shimano proprietary)
530:
377:
135:
64:
3870:
3653:Sheldon Brown's Bicycle Glossary
3516:(in Finnish). 19 December 2002.
3490:(in Swedish). Transportstyrelsen
3296:from the original on 7 June 2011
3002:Brown, Stuart F. (August 1991).
2749:Anderson, Finlay (24 May 2023).
2509:
1552:
1537:
1455:
1408:
1168:
1110:
816:
807:
303:
291:
279:
267:
255:
92:
53:
3506:
3480:
3454:
3424:
3395:
3366:
3337:
3311:
3282:
3256:
3242:
3226:
3210:
3181:
3154:
3127:
3108:
3093:
3078:
3063:
3055:Murdick, Nick (11 April 2013).
3048:
3014:
2995:
2973:
2951:
2925:
2899:
2884:
2851:
2846:Shimano Inter 8 Gear with brake
2839:
2825:
2799:
2742:
2705:
2679:
2653:
2637:
2585:
2563:
2548:
2530:
2503:
2478:
2466:
2451:
2437:"Retrobike Gallery and Archive"
2429:
2414:
2361:
2346:
2331:
2305:
2279:
2268:
2253:
2223:
2210:
2197:
2185:
1968:Bicycle and motorcycle dynamics
1727:
1627:
1387:Drum brakes are most common on
1327:'s 4-bolt pattern (proprietary)
1321:'s 3-bolt pattern (proprietary)
983:
682:U-brake on a freestyle BMX bike
544:
203:
180:
88:
49:
4383:Railroad Safety Appliance Act
4266:Westinghouse Air Brake Company
2961:. Cixi Dafeng Bicycle Co., Ltd
2594:"Bicycle Glossary: Disc Brake"
2512:"so, you like odd brakes, eh?"
2368:Juden, Chris (November 2006).
2260:Jenkins, Mike (23 July 2003).
2173:
2152:
2140:
2106:
2083:
1994:
1631:
1599:Yankee bicycle by Royce Husted
1519:
1395:, and are also often found on
1349:
1062:
623:Direct mount side pull brakes.
198:
13:
1:
3721:
3432:"Codice della strada Art. 64"
3409:(in French). 29 November 2011
2831:
2780:Loretz, Justin (1 May 2020).
2617:Annan, James (January 2006).
2358:Direct-Pull Cantilever Brakes
2262:Materials in Sports Equipment
1988:
1942:Single-lever two-wheel brakes
1637:
1559:
1331:
1120:
1097:), and are also seen on some
965:
926:
843:, are a side-pull version of
781:
776:Traditional cantilever brakes
769:
761:
442:are held in place by a metal
423:
340:
315:
186:In 1898, after the advent of
60:are less common on bicycles.
4412:Vehicle braking technologies
3696:
2235:"'safe' brakes that burn up"
2146:
1666:
940:around 1982 and licensed to
847:and mount on the same frame
388:Advantages and disadvantages
7:
3388:Regulation 4(b) applies to
2807:"Disc Brake weight listing"
2343:Adjusting Cantilever Brakes
2147:Bicycling Science (2nd ed.)
1961:
1551:More recently, large-rotor
913:. (First- and second-class
798:
673:
229:by a right-hand lever. In
179:(U.S. Patent 594,234). The
134:, which were fitted with a
103:of the bike and rider into
27:Braking device for bicycles
10:
4438:
3580:
3237:Right Front or Left Front?
2896:Brakes for Tandem Bicycles
2718:"Mount Bracket Chart 2005"
1838:of a bicycle will cause a
1677:Hydraulic brakes also use
1670:
1563:
1432:Single-speed coaster brake
1353:
1247:Caliper mounting standards
1216:Hydraulic vs. "mechanical"
1066:
1033:
786:centre-pull caliper brakes
655:Centre-pull caliper brakes
650:Centre-pull caliper brake.
642:Centre-pull caliper brakes
427:
298:Spoon brake on front wheel
114:
4330:
4279:
4243:
4150:
4019:
3983:
3922:
3879:
3868:
3807:
3250:"What is Cycle Speedway?"
3190:"How To: Emergency Stops"
2643:Sheldon Brown, quoted at
2401:
1710:
1229:Single vs. dual actuation
1158:front and rear suspension
695:centre-pull caliper brake
601:Dual-pivot caliper brake.
368:and are often mounted in
3090:Interrupter Brake Levers
2090:Hudson, William (2008).
1597:, as implemented on the
608:are used on most modern
570:Side-pull caliper brakes
4312:Emergency brake (train)
3627:Harris Cyclery Articles
3621:; et al. (n.d.f).
3264:"Plichten van fietsers"
2370:"Check your 'V' brakes"
2065:Beeley, Serena (1992).
1902:Bicycles without brakes
1292:interface along with a
1272:Disc mounting standards
1146:Other reasons include:
628:Direct mount rim brakes
578:Single pivot side-pull
44:reduces the speed of a
4158:Counter-pressure brake
3697:Whitt, Frank Rowland;
2374:Cyclists' Touring Club
2037:Clayton, Nick (1986).
1822:
1766:interrupt brake levers
1737:
1575:
1461:internally geared hubs
1450:
1445:
1444:Novo coaster brake hub
1433:
1376:
1368:
1281:
1078:
1048:
997:
899:
898:Roller cam front brake
746:
683:
651:
624:
602:
583:
484:
400:
320:Invented in 1897, the
213:
124:
37:
4178:Electromagnetic brake
3384:The National Archives
2403:US patent 4765443
2192:Parliamentary Debates
2067:A History of Bicycles
1983:List of bicycle parts
1915:Fixed gear road bikes
1804:
1735:
1686:Hydraulic brake fluid
1573:
1439:
1431:
1374:
1363:
1279:
1076:
1043:
991:
897:
744:
681:
649:
622:
600:
577:
482:
395:
211:
35:
18:Bicycle brake systems
3914:Quick release skewer
3723:Wilson, David Gordon
3699:Wilson, David Gordon
3027:Bicycle, The History
2380:on 22 September 2009
1807:mechanical advantage
1778:mechanical advantage
1720:the standard cable.
1618:Actuation mechanisms
1090:, or hydraulically.
1052:Hydraulic rim brakes
1030:Hydraulic rim brakes
1007:mechanical advantage
923:mechanical advantage
614:mechanical advantage
552:mechanical advantage
231:developing countries
4292:Diesel brake tender
3690:on 6 February 2009.
3670:Heine, Jan (2008).
3221:Braking and Turning
3163:"Using your Brakes"
2665:Cyclocross Magazine
2207:, September 2, 1902
2116:, November 23, 1897
1978:Glossary of cycling
1821:it is moved inward.
1657:rod-actuated brakes
1624:actuation mechanism
1047:hydraulic rim brake
634:and released as an
562:, particularly the
475:Rod-actuated brakes
467:Types of rim brakes
173:Dunlop Tyre Company
4373:Pearson's Coupling
4260:New York Air Brake
4251:Faiveley Transport
4220:Regenerative brake
4213:Railway disc brake
4173:Eddy current brake
4163:Countersteam brake
3649:"Bicycle Glossary"
3599:. Harris Cyclery.
3488:"Regler för cykel"
3436:Gazzetta ufficiale
3403:"Code de la route"
3379:legislation.gov.uk
3004:"The Anybody Bike"
2859:"Repack Revisited"
2848:Cykelkram Bikeblog
2625:on 20 October 2007
2149:, pp.153–154
2136:Patent No. 594,234
1840:transfer of weight
1823:
1738:
1576:
1446:
1440:Cutaway view of a
1434:
1377:
1369:
1282:
1079:
1049:
998:
974:recumbent bicycles
934:Charlie Cunningham
900:
837:direct-pull brakes
833:Linear-pull brakes
762:direct-pull brakes
747:
684:
652:
625:
603:
584:
497:roller lever brake
489:rod-actuated brake
485:
401:
335:motorized bicycles
214:
38:
4394:
4393:
4353:Dead man's switch
4203:Railway air brake
4198:Kunze-Knorr brake
4110:
4109:
3729:Bicycling Science
3703:Bicycling Science
3676:Bicycle Quarterly
3165:. John S. Allen.
3105:Brake Lever Types
3022:Herlihy, David V.
2833:Bicycling Science
2667:. 7 December 2010
2160:Bicycling Science
2016:978-0-262-02675-8
1830:Braking technique
1815:cantilever brakes
1755:extension levers,
1286:industry standard
1015:Bicycle Quarterly
907:cantilever brakes
903:Roller cam brakes
890:Roller cam brakes
880:cantilever brakes
845:cantilever brakes
782:direct-pull brake
766:roller cam brakes
758:cantilever brakes
717:Cantilever brakes
699:roller cam brakes
326:Duck roller brake
177:Duck Roller Brake
16:(Redirected from
4429:
4386:
4137:
4130:
4123:
4114:
4113:
3874:
3794:
3787:
3780:
3771:
3770:
3765:
3744:
3732:
3716:
3691:
3686:. Archived from
3664:
3662:
3660:
3655:. Harris Cyclery
3638:
3636:
3634:
3629:. Harris Cyclery
3612:
3610:
3608:
3591:(October 2005).
3575:
3574:
3572:
3570:
3555:
3549:
3548:
3546:
3544:
3529:
3523:
3522:
3510:
3504:
3503:
3497:
3495:
3484:
3478:
3477:
3471:
3469:
3458:
3452:
3451:
3445:
3443:
3428:
3422:
3421:
3416:
3414:
3399:
3393:
3387:
3370:
3364:
3363:
3358:
3356:
3341:
3335:
3334:
3328:
3326:
3315:
3309:
3308:
3303:
3301:
3286:
3280:
3279:
3273:
3271:
3260:
3254:
3253:
3246:
3240:
3230:
3224:
3214:
3208:
3207:
3202:
3200:
3188:McCready, Bill.
3185:
3179:
3178:
3176:
3174:
3158:
3152:
3151:
3149:
3147:
3134:Brown, Sheldon.
3131:
3125:
3122:
3116:
3112:
3106:
3097:
3091:
3082:
3076:
3075:Extension levers
3067:
3061:
3060:
3059:. bikerumor.com.
3052:
3046:
3045:
3018:
3012:
3011:
2999:
2993:
2992:
2990:
2988:
2981:"Yankee Bicycle"
2977:
2971:
2970:
2968:
2966:
2955:
2949:
2948:
2946:
2944:
2929:
2923:
2922:
2920:
2918:
2903:
2897:
2888:
2882:
2873:
2867:
2866:
2855:
2849:
2843:
2837:
2829:
2823:
2822:
2820:
2818:
2803:
2797:
2796:
2794:
2792:
2777:
2766:
2765:
2763:
2761:
2746:
2740:
2739:
2737:
2735:
2729:
2723:. Archived from
2722:
2709:
2703:
2702:
2700:
2698:
2683:
2677:
2676:
2674:
2672:
2657:
2651:
2641:
2635:
2634:
2632:
2630:
2621:. Archived from
2614:
2608:
2607:
2602:
2600:
2592:Brown, Sheldon.
2589:
2583:
2582:
2580:
2578:
2567:
2561:
2552:
2546:
2545:
2534:
2528:
2527:
2525:
2523:
2507:
2501:
2500:
2482:
2476:
2470:
2464:
2455:
2449:
2447:
2445:
2443:
2433:
2427:
2426:Roller-cam Brake
2418:
2412:
2411:
2410:
2406:
2399:
2390:
2389:
2387:
2385:
2376:. Archived from
2365:
2359:
2350:
2344:
2335:
2329:
2328:
2326:
2324:
2309:
2303:
2302:
2300:
2298:
2283:
2277:
2272:
2266:
2265:
2257:
2251:
2250:
2248:
2246:
2237:. Archived from
2227:
2221:
2214:
2208:
2203:Bill, Louis H.,
2201:
2195:
2189:
2183:
2177:
2171:
2156:
2150:
2144:
2138:
2134:Duck, Abram W.,
2132:
2117:
2112:Duck, Abram W.,
2110:
2104:
2103:
2101:
2099:
2087:
2081:
2080:
2062:
2053:
2052:
2034:
2021:
2020:
1998:
1494:
1493:
1489:
1454:), is a type of
1453:
1420:applied forces.
1389:utility bicycles
1367:front drum brake
1238:Multiple pistons
1103:touring bicycles
905:are centre-pull
820:
811:
723:cantilever brake
307:
295:
283:
271:
259:
129:
21:
4437:
4436:
4432:
4431:
4430:
4428:
4427:
4426:
4397:
4396:
4395:
4390:
4385:(United States)
4384:
4368:Hydraulic brake
4326:
4322:Dowty retarders
4275:
4239:
4188:Heberlein brake
4146:
4141:
4111:
4106:
4102:Training wheels
4062:Luggage carrier
4015:
3979:
3918:
3875:
3866:
3803:
3798:
3768:
3762:
3741:
3713:
3658:
3656:
3632:
3630:
3606:
3604:
3583:
3578:
3568:
3566:
3564:Huffington Post
3556:
3552:
3542:
3540:
3530:
3526:
3512:
3511:
3507:
3493:
3491:
3486:
3485:
3481:
3467:
3465:
3460:
3459:
3455:
3441:
3439:
3430:
3429:
3425:
3412:
3410:
3401:
3400:
3396:
3386:. SI 1983/1176.
3372:
3371:
3367:
3354:
3352:
3342:
3338:
3324:
3322:
3317:
3316:
3312:
3299:
3297:
3288:
3287:
3283:
3269:
3267:
3262:
3261:
3257:
3248:
3247:
3243:
3231:
3227:
3215:
3211:
3198:
3196:
3186:
3182:
3172:
3170:
3161:Allen, John S.
3159:
3155:
3145:
3143:
3132:
3128:
3123:
3119:
3113:
3109:
3098:
3094:
3083:
3079:
3068:
3064:
3053:
3049:
3042:
3019:
3015:
3008:Popular Science
3000:
2996:
2986:
2984:
2979:
2978:
2974:
2964:
2962:
2957:
2956:
2952:
2942:
2940:
2939:on 18 July 2010
2933:"Star Bicycles"
2931:
2930:
2926:
2916:
2914:
2905:
2904:
2900:
2889:
2885:
2874:
2870:
2857:
2856:
2852:
2844:
2840:
2830:
2826:
2816:
2814:
2805:
2804:
2800:
2790:
2788:
2778:
2769:
2759:
2757:
2747:
2743:
2733:
2731:
2730:on 11 July 2011
2727:
2720:
2716:
2710:
2706:
2696:
2694:
2693:. 31 March 2014
2685:
2684:
2680:
2670:
2668:
2659:
2658:
2654:
2642:
2638:
2628:
2626:
2615:
2611:
2598:
2596:
2590:
2586:
2576:
2574:
2568:
2564:
2553:
2549:
2544:. 14 July 2019.
2536:
2535:
2531:
2521:
2519:
2508:
2504:
2497:
2483:
2479:
2471:
2467:
2456:
2452:
2441:
2439:
2435:
2434:
2430:
2419:
2415:
2408:
2400:
2393:
2383:
2381:
2366:
2362:
2351:
2347:
2336:
2332:
2322:
2320:
2310:
2306:
2296:
2294:
2284:
2280:
2273:
2269:
2258:
2254:
2244:
2242:
2241:on 4 April 2010
2228:
2224:
2218:George A. Wyman
2215:
2211:
2202:
2198:
2190:
2186:
2178:
2174:
2157:
2153:
2145:
2141:
2133:
2120:
2111:
2107:
2097:
2095:
2088:
2084:
2077:
2063:
2056:
2049:
2035:
2024:
2017:
2009:. p. 259.
1999:
1995:
1991:
1964:
1944:
1904:
1855:tandem bicycles
1836:motion dynamics
1832:
1750:drop handlebars
1730:
1713:
1688:
1675:
1673:Hydraulic brake
1669:
1640:
1620:
1568:
1562:
1522:
1491:
1487:
1486:
1426:
1405:tandem bicycles
1358:
1352:
1334:
1319:Hope Technology
1274:
1265:
1249:
1240:
1231:
1223:drop handlebars
1218:
1213:
1171:
1123:
1107:racing bicycles
1099:hybrid bicycles
1071:
1065:
1038:
1036:Hydraulic brake
1032:
986:
892:
830:
829:
828:
827:
823:
822:
821:
813:
812:
801:
778:
719:
676:
644:
610:racing bicycles
572:
533:
477:
469:
432:
426:
390:
380:mounted on the
343:
337:(motorcycles).
318:
311:
308:
299:
296:
287:
284:
275:
272:
263:
260:
226:penny farthings
206:
201:
169:pneumatic tyres
143:penny-farthings
117:
77:hydraulic hoses
28:
23:
22:
15:
12:
11:
5:
4435:
4425:
4424:
4422:Bicycle brakes
4419:
4414:
4409:
4392:
4391:
4389:
4388:
4380:
4375:
4370:
4365:
4363:Engine braking
4360:
4355:
4350:
4345:
4340:
4334:
4332:
4331:Related topics
4328:
4327:
4325:
4324:
4319:
4314:
4309:
4304:
4299:
4294:
4289:
4283:
4281:
4277:
4276:
4274:
4273:
4268:
4263:
4253:
4247:
4245:
4241:
4240:
4238:
4237:
4232:
4227:
4222:
4217:
4216:
4215:
4205:
4200:
4195:
4190:
4185:
4180:
4175:
4170:
4165:
4160:
4154:
4152:
4148:
4147:
4144:Railway brakes
4140:
4139:
4132:
4125:
4117:
4108:
4107:
4105:
4104:
4099:
4094:
4089:
4084:
4079:
4074:
4069:
4064:
4059:
4054:
4049:
4044:
4039:
4034:
4029:
4023:
4021:
4017:
4016:
4014:
4013:
4008:
4003:
3998:
3993:
3987:
3985:
3981:
3980:
3978:
3977:
3972:
3967:
3958:
3953:
3948:
3939:
3934:
3928:
3926:
3920:
3919:
3917:
3916:
3911:
3906:
3901:
3896:
3891:
3885:
3883:
3877:
3876:
3869:
3867:
3865:
3864:
3859:
3854:
3852:Bottom bracket
3849:
3844:
3839:
3834:
3829:
3824:
3819:
3813:
3811:
3805:
3804:
3797:
3796:
3789:
3782:
3774:
3767:
3766:
3760:
3746:
3745:
3739:
3725:(April 2004).
3718:
3717:
3711:
3693:
3692:
3666:
3665:
3645:Brown, Sheldon
3640:
3639:
3619:Brown, Sheldon
3614:
3613:
3584:
3582:
3579:
3577:
3576:
3550:
3524:
3519:jarrulaitetta.
3505:
3479:
3453:
3423:
3394:
3365:
3336:
3310:
3281:
3255:
3241:
3225:
3209:
3194:Santana Cycles
3180:
3153:
3126:
3117:
3107:
3092:
3077:
3062:
3047:
3040:
3013:
2994:
2972:
2950:
2924:
2898:
2883:
2868:
2850:
2838:
2824:
2798:
2767:
2741:
2704:
2678:
2652:
2636:
2609:
2584:
2562:
2547:
2529:
2502:
2495:
2477:
2465:
2450:
2428:
2413:
2391:
2360:
2345:
2330:
2304:
2278:
2267:
2252:
2231:Forester, John
2222:
2209:
2196:
2184:
2172:
2151:
2139:
2118:
2105:
2082:
2075:
2054:
2047:
2039:Early Bicycles
2022:
2015:
1992:
1990:
1987:
1986:
1985:
1980:
1975:
1970:
1963:
1960:
1943:
1940:
1932:Cycle speedway
1907:Track bicycles
1903:
1900:
1895:
1894:
1891:
1887:
1883:
1879:
1875:
1872:
1869:
1831:
1828:
1819:caliper brakes
1799:
1798:
1792:
1762:suicide levers
1758:safety levers
1748:Bicycles with
1729:
1726:
1712:
1709:
1687:
1684:
1671:Main article:
1668:
1665:
1653:Coaster brakes
1639:
1636:
1619:
1616:
1595:rim band brake
1564:Main article:
1561:
1558:
1521:
1518:
1506:Sturmey-Archer
1499:, such as the
1425:
1424:Coaster brakes
1422:
1365:Sturmey-Archer
1354:Main article:
1351:
1348:
1333:
1330:
1329:
1328:
1322:
1316:
1313:
1273:
1270:
1264:
1261:
1248:
1245:
1239:
1236:
1230:
1227:
1217:
1214:
1212:
1211:
1207:
1200:
1191:
1189:
1188:
1184:
1177:
1172:
1170:
1167:
1166:
1165:
1161:
1154:
1151:
1144:
1143:
1140:
1137:
1134:
1131:
1122:
1119:
1095:downhill bikes
1067:Main article:
1064:
1061:
1034:Main article:
1031:
1028:
985:
982:
946:mountain bikes
891:
888:
825:
824:
815:
814:
806:
805:
804:
803:
802:
800:
797:
777:
774:
751:mountain bikes
718:
715:
675:
672:
664:straddle cable
643:
640:
571:
568:
556:mountain bikes
539:is a class of
532:
531:Caliper brakes
529:
476:
473:
468:
465:
440:cartridge type
428:Main article:
425:
422:
389:
386:
342:
339:
317:
314:
313:
312:
309:
302:
300:
297:
290:
288:
285:
278:
276:
273:
266:
264:
261:
254:
205:
202:
200:
197:
192:coaster brakes
161:safety bicycle
116:
113:
105:thermal energy
101:kinetic energy
26:
9:
6:
4:
3:
2:
4434:
4423:
4420:
4418:
4415:
4413:
4410:
4408:
4407:Bicycle parts
4405:
4404:
4402:
4387:
4381:
4379:
4376:
4374:
4371:
4369:
4366:
4364:
4361:
4359:
4356:
4354:
4351:
4349:
4346:
4344:
4343:Bicycle brake
4341:
4339:
4336:
4335:
4333:
4329:
4323:
4320:
4318:
4315:
4313:
4310:
4308:
4305:
4303:
4300:
4298:
4295:
4293:
4290:
4288:
4285:
4284:
4282:
4280:Other aspects
4278:
4272:
4269:
4267:
4264:
4261:
4257:
4254:
4252:
4249:
4248:
4246:
4244:Manufacturers
4242:
4236:
4233:
4231:
4228:
4226:
4223:
4221:
4218:
4214:
4211:
4210:
4209:
4206:
4204:
4201:
4199:
4196:
4194:
4191:
4189:
4186:
4184:
4183:Exhaust brake
4181:
4179:
4176:
4174:
4171:
4169:
4168:Dynamic brake
4166:
4164:
4161:
4159:
4156:
4155:
4153:
4149:
4145:
4138:
4133:
4131:
4126:
4124:
4119:
4118:
4115:
4103:
4100:
4098:
4095:
4093:
4090:
4088:
4085:
4083:
4080:
4078:
4075:
4073:
4070:
4068:
4065:
4063:
4060:
4058:
4055:
4053:
4050:
4048:
4047:Cyclocomputer
4045:
4043:
4040:
4038:
4035:
4033:
4030:
4028:
4025:
4024:
4022:
4018:
4012:
4009:
4007:
4004:
4002:
3999:
3997:
3994:
3992:
3989:
3988:
3986:
3982:
3976:
3973:
3971:
3968:
3966:
3962:
3959:
3957:
3954:
3952:
3949:
3947:
3943:
3940:
3938:
3935:
3933:
3930:
3929:
3927:
3925:
3921:
3915:
3912:
3910:
3907:
3905:
3902:
3900:
3897:
3895:
3892:
3890:
3887:
3886:
3884:
3882:
3878:
3873:
3863:
3860:
3858:
3855:
3853:
3850:
3848:
3845:
3843:
3840:
3838:
3835:
3833:
3830:
3828:
3825:
3823:
3820:
3818:
3815:
3814:
3812:
3810:
3806:
3802:
3801:Bicycle parts
3795:
3790:
3788:
3783:
3781:
3776:
3775:
3772:
3763:
3761:91-518-3906-7
3757:
3753:
3752:Ă„lskade cykel
3748:
3747:
3742:
3740:0-262-73154-1
3736:
3731:
3730:
3724:
3720:
3719:
3714:
3712:0-262-23111-5
3708:
3704:
3700:
3695:
3694:
3689:
3685:
3681:
3677:
3673:
3668:
3667:
3654:
3650:
3646:
3642:
3641:
3628:
3624:
3620:
3616:
3615:
3602:
3598:
3594:
3590:
3589:Brandt, Jobst
3586:
3585:
3565:
3561:
3554:
3539:
3535:
3528:
3520:
3515:
3509:
3501:
3489:
3483:
3475:
3463:
3457:
3449:
3437:
3433:
3427:
3420:
3408:
3404:
3398:
3391:
3385:
3381:
3380:
3375:
3369:
3362:
3351:
3347:
3340:
3332:
3320:
3314:
3307:
3295:
3291:
3285:
3277:
3265:
3259:
3251:
3245:
3238:
3234:
3229:
3222:
3218:
3213:
3206:
3195:
3191:
3184:
3168:
3164:
3157:
3141:
3137:
3130:
3121:
3111:
3104:
3101:
3096:
3089:
3086:
3081:
3074:
3071:
3066:
3058:
3051:
3043:
3041:0-300-10418-9
3037:
3033:
3029:
3028:
3023:
3017:
3009:
3005:
2998:
2982:
2976:
2960:
2954:
2938:
2934:
2928:
2912:
2908:
2902:
2895:
2892:
2887:
2880:
2877:
2872:
2864:
2860:
2854:
2847:
2842:
2835:
2834:
2828:
2812:
2808:
2802:
2787:
2783:
2776:
2774:
2772:
2756:
2752:
2745:
2726:
2719:
2714:
2708:
2692:
2688:
2682:
2666:
2662:
2656:
2649:
2646:
2640:
2624:
2620:
2613:
2606:
2595:
2588:
2573:
2566:
2559:
2556:
2551:
2543:
2539:
2533:
2517:
2513:
2506:
2498:
2496:0-914578-09-X
2492:
2488:
2481:
2474:
2469:
2463:
2459:
2454:
2438:
2432:
2425:
2422:
2417:
2404:
2398:
2396:
2379:
2375:
2371:
2364:
2357:
2354:
2349:
2342:
2339:
2334:
2319:
2315:
2308:
2293:
2289:
2282:
2276:
2271:
2263:
2256:
2240:
2236:
2232:
2226:
2219:
2213:
2206:
2200:
2193:
2188:
2181:
2176:
2169:
2168:0-262-23111-5
2165:
2161:
2155:
2148:
2143:
2137:
2131:
2129:
2127:
2125:
2123:
2115:
2109:
2094:. Jim Langley
2093:
2086:
2078:
2076:1-85170-753-0
2072:
2068:
2061:
2059:
2050:
2048:0-85263-803-5
2044:
2040:
2033:
2031:
2029:
2027:
2018:
2012:
2008:
2004:
1997:
1993:
1984:
1981:
1979:
1976:
1974:
1971:
1969:
1966:
1965:
1959:
1956:
1952:
1949:
1939:
1936:
1933:
1929:
1925:
1921:
1916:
1912:
1908:
1899:
1892:
1888:
1884:
1880:
1876:
1873:
1870:
1867:
1866:
1865:
1862:
1860:
1856:
1851:
1849:
1845:
1841:
1837:
1827:
1820:
1816:
1812:
1808:
1805:This lever’s
1803:
1796:
1793:
1790:
1789:Standard pull
1787:
1786:
1785:
1782:
1779:
1774:
1772:
1767:
1763:
1759:
1756:
1751:
1746:
1743:
1734:
1725:
1721:
1718:
1708:
1705:
1701:
1697:
1693:
1683:
1680:
1674:
1664:
1662:
1658:
1654:
1649:
1648:Bowden cables
1645:
1635:
1633:
1629:
1625:
1615:
1613:
1609:
1604:
1600:
1596:
1591:
1589:
1585:
1581:
1572:
1567:
1557:
1554:
1549:
1547:
1546:Bowden cables
1543:
1539:
1535:
1529:
1527:
1517:
1515:
1509:
1507:
1502:
1498:
1483:
1481:
1476:
1474:
1469:
1464:
1462:
1457:
1452:
1443:
1438:
1430:
1421:
1418:
1417:quick release
1412:
1410:
1406:
1402:
1398:
1394:
1390:
1385:
1381:
1373:
1366:
1362:
1357:
1347:
1345:
1340:
1326:
1323:
1320:
1317:
1314:
1311:
1310:
1309:
1306:
1303:
1300:
1295:
1291:
1287:
1278:
1269:
1260:
1258:
1254:
1244:
1235:
1226:
1224:
1208:
1205:
1201:
1197:
1192:
1185:
1181:
1180:
1178:
1174:
1173:
1169:Disadvantages
1162:
1159:
1155:
1152:
1149:
1148:
1147:
1141:
1138:
1135:
1132:
1128:
1127:
1126:
1118:
1114:
1112:
1108:
1104:
1100:
1096:
1091:
1089:
1084:
1075:
1070:
1060:
1057:
1053:
1046:
1042:
1037:
1027:
1025:
1020:
1017:
1016:
1010:
1008:
1003:
995:
990:
981:
977:
975:
971:
967:
963:
959:
955:
951:
947:
943:
939:
935:
930:
928:
924:
920:
916:
912:
908:
904:
896:
887:
883:
881:
877:
873:
872:Mini V-brakes
869:
865:
861:
857:
854:
850:
846:
842:
838:
834:
819:
810:
796:
793:
789:
787:
783:
773:
771:
767:
763:
759:
754:
752:
743:
739:
736:
732:
728:
724:
714:
711:
710:Freestyle BMX
706:
702:
700:
696:
692:
688:
680:
671:
667:
665:
661:
656:
648:
639:
637:
636:open standard
633:
629:
621:
617:
615:
611:
607:
599:
595:
591:
588:
581:
576:
567:
565:
561:
557:
553:
548:
546:
542:
538:
537:caliper brake
528:
526:
525:Flying Pigeon
522:
518:
513:
508:
506:
502:
501:Bowden cables
498:
494:
490:
481:
472:
464:
460:
456:
452:
449:
445:
441:
437:
431:
421:
417:
413:
409:
406:
398:
394:
385:
383:
379:
375:
371:
367:
363:
359:
355:
351:
347:
338:
336:
332:
327:
323:
306:
301:
294:
289:
282:
277:
270:
265:
258:
253:
252:
251:
249:
244:
241:
239:
236:
232:
227:
223:
222:plunger brake
219:
210:
196:
193:
189:
184:
182:
178:
174:
170:
165:
162:
157:
155:
154:caliper brake
150:
146:
144:
139:
137:
133:
128:
127:
121:
112:
110:
106:
102:
98:
94:
90:
86:
85:bicycle chain
82:
78:
74:
73:Bowden cables
70:
66:
61:
59:
55:
51:
47:
43:
42:bicycle brake
34:
30:
19:
4342:
4256:Knorr-Bremse
4235:Vacuum brake
4005:
3996:Bowden cable
3899:Spoke nipple
3751:
3728:
3702:
3688:the original
3675:
3657:. Retrieved
3652:
3631:. Retrieved
3626:
3605:. Retrieved
3596:
3567:. Retrieved
3563:
3553:
3541:. Retrieved
3537:
3527:
3517:
3508:
3499:
3492:. Retrieved
3482:
3473:
3466:. Retrieved
3456:
3447:
3440:. Retrieved
3438:(in Italian)
3435:
3426:
3418:
3411:. Retrieved
3406:
3397:
3377:
3368:
3360:
3353:. Retrieved
3350:The Guardian
3349:
3339:
3330:
3323:. Retrieved
3313:
3305:
3298:. Retrieved
3284:
3275:
3268:. Retrieved
3258:
3244:
3228:
3212:
3204:
3197:. Retrieved
3192:. President
3183:
3171:. Retrieved
3156:
3144:. Retrieved
3129:
3120:
3110:
3095:
3080:
3065:
3050:
3026:
3016:
3010:: 58–59, 89.
3007:
2997:
2985:. Retrieved
2975:
2963:. Retrieved
2953:
2941:. Retrieved
2937:the original
2927:
2915:. Retrieved
2901:
2886:
2871:
2862:
2853:
2841:
2832:
2827:
2815:. Retrieved
2801:
2789:. Retrieved
2785:
2758:. Retrieved
2754:
2744:
2732:. Retrieved
2725:the original
2707:
2695:. Retrieved
2690:
2681:
2669:. Retrieved
2664:
2655:
2639:
2627:. Retrieved
2623:the original
2612:
2604:
2597:. Retrieved
2587:
2575:. Retrieved
2565:
2550:
2541:
2532:
2520:. Retrieved
2510:Metz, Joel.
2505:
2486:
2480:
2475:, p. 36
2468:
2453:
2440:. Retrieved
2431:
2416:
2382:. Retrieved
2378:the original
2363:
2348:
2333:
2321:. Retrieved
2317:
2307:
2295:. Retrieved
2291:
2281:
2270:
2261:
2255:
2243:. Retrieved
2239:the original
2225:
2212:
2204:
2199:
2191:
2187:
2179:
2175:
2159:
2154:
2142:
2135:
2113:
2108:
2098:22 September
2096:. Retrieved
2085:
2066:
2038:
2002:
1996:
1957:
1953:
1945:
1937:
1905:
1896:
1863:
1852:
1833:
1824:
1794:
1788:
1783:
1775:
1765:
1761:
1757:
1754:
1747:
1739:
1728:Brake levers
1722:
1714:
1689:
1679:brake levers
1676:
1661:Spoon brakes
1644:brake levers
1641:
1623:
1621:
1594:
1592:
1579:
1577:
1550:
1530:
1525:
1523:
1510:
1484:
1477:
1465:
1451:contropedale
1447:
1413:
1386:
1382:
1378:
1335:
1307:
1304:
1283:
1266:
1256:
1252:
1250:
1241:
1232:
1219:
1145:
1124:
1115:
1092:
1082:
1080:
1051:
1050:
1021:
1013:
1011:
1001:
999:
996:delta brakes
984:Delta brakes
978:
931:
919:cam follower
902:
901:
884:
875:
871:
870:
866:
862:
858:
840:
836:
832:
831:
794:
790:
779:
755:
748:
722:
720:
707:
703:
690:
686:
685:
668:
663:
654:
653:
627:
626:
605:
604:
592:
586:
585:
549:
536:
534:
519:such as the
509:
505:Westwood rim
496:
492:
491:, or simply
488:
486:
470:
461:
457:
453:
446:or threaded
433:
418:
414:
410:
402:
345:
344:
330:
325:
321:
319:
245:
242:
221:
217:
215:
204:Spoon brakes
185:
176:
166:
158:
151:
147:
140:
126:Laufmaschine
118:
65:brake levers
62:
41:
39:
29:
4230:Track brake
4225:Steam brake
4092:Skirt guard
4037:Bottle cage
4020:Peripherals
4001:Cable guide
3951:Master link
3464:(in Danish)
3235:, p. "
3233:Brown n.d.f
3219:, p. *
3217:Brown n.d.f
3173:25 December
3146:15 December
2891:Brown n.d.f
2650:Disc Brakes
2645:Brandt 2005
2599:22 November
2577:23 December
2560:Disc Brakes
2555:Brandt 2005
2458:Brandt 2005
2353:Brown n.d.f
2338:Brown n.d.f
1928:spoon brake
1771:cyclo-cross
1704:mineral oil
1700:hygroscopic
1646:coupled to
1614:standards.
1553:disc brakes
1520:Drag brakes
1497:derailleurs
1401:velomobiles
1397:cargo bikes
1393:Netherlands
1350:Drum brakes
1344:absorb heat
1183:components.
1063:Disc brakes
1002:delta brake
958:chain stays
950:fork blades
218:spoon brake
199:Brake types
136:spoon brake
58:Drum brakes
54:disc brakes
4401:Categories
4378:Pneumatics
4358:Drum brake
4208:Disc brake
4193:Hand brake
4087:Reflectors
4082:Spoke card
3961:Derailleur
3924:Drivetrain
3904:Valve stem
3862:Suspension
3817:Handlebars
3607:22 January
3468:28 October
3407:Legifrance
3102:, p.
3100:Brown 2007
3087:, p.
3085:Brown 2007
3072:, p.
3070:Brown 2007
2983:. US Times
2893:, p.
2881:Drag Brake
2878:, p.
2876:Brown 2007
2817:7 November
2791:7 November
2760:7 November
2647:, p.
2629:19 October
2557:, p.
2522:1 February
2473:Heine 2008
2460:, p.
2423:, p.
2421:Brown 2007
2384:6 February
2355:, p.
2340:, p.
2323:7 November
2297:7 November
1989:References
1878:handlebar.
1859:recumbents
1742:handlebars
1698:which are
1638:Mechanical
1628:mechanical
1608:band brake
1588:freewheels
1580:band brake
1566:Band brake
1560:Band brake
1538:drum brake
1526:drag brake
1504:SRC3 from
1473:Birmingham
1456:drum brake
1409:drag brake
1356:Drum brake
1339:moment arm
1332:Disc sizes
1257:post-mount
1196:brake fade
1121:Advantages
1111:drag brake
1083:disc brake
1069:Disc brake
1024:Campagnolo
994:Campagnolo
992:A pair of
954:seat stays
560:road bikes
448:grub screw
436:brake shoe
424:Brake pads
346:Rim brakes
341:Rim brakes
331:duck brake
322:Duck brake
316:Duck brake
181:Duck brake
132:boneshaker
120:Karl Drais
109:dissipated
50:rim brakes
4338:Air brake
4287:Brake van
4077:Saddlebag
4067:Mudguards
4052:Kickstand
3970:Gear case
3965:Hub gears
3827:Head tube
3684:1941-8809
2863:sonic.net
2755:BikeRadar
2671:17 August
2292:BikeRadar
2194:, p. 4951
2007:MIT Press
1973:Detangler
1924:detangler
1911:velodrome
1795:Long pull
1667:Hydraulic
1632:hydraulic
1442:Husqvarna
1187:heavier).
727:seat stay
691:990-style
590:the rim.
517:roadsters
493:rod brake
444:split pin
430:Brake pad
397:Aluminium
382:handlebar
238:roadsters
235:rod brake
188:freewheel
83:, or the
4317:Retarder
4072:Panniers
4057:Lighting
3975:Sprocket
3937:Crankset
3857:Fork end
3842:Seatpost
3701:(1982).
3647:(2007).
3601:Archived
3494:24 April
3413:29 March
3294:Archived
3270:10 April
3167:Archived
3140:Archived
3024:(2004).
2911:Archived
2811:Archived
2516:Archived
2442:3 August
1962:See also
1948:SureStop
1886:control.
1844:traction
1811:V-Brakes
1534:blow out
1514:Downhill
1403:. Older
1294:lockring
927:U-brakes
841:V-brakes
799:V-brakes
770:U-brakes
687:U-brakes
674:U-brakes
97:friction
4042:Fairing
4011:Ferrule
3991:Shifter
3984:Cabling
3909:Dustcap
3832:Headset
3659:21 June
3633:21 June
3581:Sources
3390:e-bikes
3355:20 July
3325:27 July
3199:12 July
2987:2 April
2965:2 April
2943:2 April
2917:2 April
2786:road.cc
2734:15 June
2691:road.cc
2542:road.cc
2318:road.cc
1890:brakes.
1717:Santana
1696:DOT 5.1
1490:⁄
1325:Rohloff
1290:splined
1204:pannier
966:U-brake
942:Suntour
876:mini Vs
632:Shimano
580:caliper
358:leather
352:to the
171:by the
115:History
89:caliper
46:bicycle
4417:Brakes
4097:Fender
4027:Basket
3956:Cogset
3881:Wheels
3847:Saddle
3758:
3737:
3709:
3682:
3569:7 June
3543:15 May
3300:2 July
3115:hard."
3038:
2697:13 May
2493:
2409:
2245:5 June
2166:
2073:
2045:
2013:
1711:Hybrid
1603:kevlar
1468:clutch
1199:discs.
1056:trials
1045:Magura
849:bosses
582:brake.
521:Sohrab
362:rubber
107:to be
69:pedals
4348:Brake
4151:Types
4006:Brake
3942:Chain
3932:Pedal
3894:Spoke
3809:Frame
3442:7 May
2728:(PDF)
2721:(PDF)
2713:Hayes
2462:Delta
1692:DOT 4
1501:Sachs
1088:cable
962:crank
915:lever
853:cable
735:lever
541:cable
378:lever
374:shoes
370:metal
4032:Bell
3946:Belt
3889:Tire
3837:Fork
3822:Stem
3756:ISBN
3735:ISBN
3707:ISBN
3680:ISSN
3661:2010
3635:2010
3609:2009
3571:2018
3545:2018
3496:2021
3470:2012
3444:2024
3415:2014
3357:2011
3327:2012
3302:2011
3272:2015
3201:2012
3175:2010
3148:2010
3036:ISBN
2989:2010
2967:2010
2945:2010
2919:2010
2819:2006
2793:2023
2762:2023
2736:2010
2699:2014
2673:2012
2631:2007
2601:2011
2579:2012
2524:2010
2491:ISBN
2444:2009
2386:2010
2325:2023
2299:2023
2247:2010
2164:ISBN
2100:2009
2071:ISBN
2043:ISBN
2011:ISBN
1946:The
1848:endo
1834:The
1817:and
1776:The
1622:The
1584:drum
1542:Arai
1399:and
1101:and
1000:The
972:and
952:and
874:(or
768:and
760:and
731:fork
721:The
660:yoke
535:The
523:and
512:fork
487:The
405:rims
366:cork
350:pads
248:West
216:The
93:drum
81:rods
52:and
3538:Inc
1920:BMX
1853:On
1694:or
1630:or
1255:or
970:BMX
938:WTB
936:of
911:cam
835:or
729:or
545:rim
364:or
354:rim
324:or
220:or
91:or
67:or
4403::
3674:.
3651:.
3625:.
3595:.
3562:.
3536:.
3498:.
3472:.
3446:.
3434:.
3417:.
3405:.
3382:.
3376:.
3359:.
3348:.
3329:.
3304:.
3292:.
3274:.
3203:.
3138:.
3034:.
3032:76
3006:.
2861:.
2809:.
2784:.
2770:^
2753:.
2689:.
2663:.
2603:.
2540:.
2514:.
2394:^
2372:.
2316:.
2290:.
2233:.
2121:^
2057:^
2025:^
2005:.
1930:.
1773:.
1634:.
1593:A
1578:A
1524:A
1463:.
1411:.
1299:BB
1253:IS
1081:A
976:.
566:.
527:.
384:.
360:,
111:.
99:,
79:,
75:,
56:.
40:A
4262:)
4258:(
4136:e
4129:t
4122:v
3963:/
3944:/
3793:e
3786:t
3779:v
3764:.
3743:.
3715:.
3663:.
3637:.
3611:.
3573:.
3547:.
3252:.
3239:"
3223:"
3177:.
3150:.
3044:.
2991:.
2969:.
2947:.
2921:.
2865:.
2821:.
2795:.
2764:.
2738:.
2701:.
2675:.
2633:.
2581:.
2526:.
2499:.
2446:.
2388:.
2327:.
2301:.
2249:.
2102:.
2079:.
2051:.
2019:.
1492:8
1488:1
1160:.
658:"
495:(
372:"
20:)
Text is available under the Creative Commons Attribution-ShareAlike License. Additional terms may apply.